Reply
New Member
Posts: 24
Registered: ‎01-30-2018
Solutions: 1

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Multiple ER-4 and ER-6P successfully upgraded with my self-hosted UNMS controller. Happy to see fail-over fixes as that is a primary reason for these to be deployed at a site. No issues in the past days and no complaints from the clients!

New Member
Posts: 22
Registered: ‎09-06-2015
Kudos: 39

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Looks like the issues around endianess that I reported/resolved back in April still arent fixed.  Neither is the ordering issue around hw_nat.  I went ahead and sent PM to @UBNT-Jordan, who I contacted in Septermber to get the ball rolling on getting them pushed over the finish line. If there is a better contact to follow up on these issues, let me know.

New Member
Posts: 13
Registered: ‎10-15-2016

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

ER-4 Upgraded without a hitch...Thanks!

New Member
Posts: 14
Registered: ‎06-30-2018
Kudos: 1

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

ERX upgraded fine ... seems to be working.

 

I noticed the title of the GUI is now just "- ubnt" which if you run a commit from the WebCLI goes to "- ubnt - ubnt", previously was "EdgeOS - ubnt". Havent noticed any other isssues, cpu usage seems to hover around 3% now but haven done any digging on that.

Emerging Member
Posts: 44
Registered: ‎09-30-2014
Kudos: 1
Solutions: 2

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

another issue with ER-4

 

admin@gw:~$ show ubnt offload flows
cat: read error: Cannot allocate memory
admin@gw:~$ cat /proc/meminfo
MemTotal:         997100 kB
MemFree:          608936 kB
Buffers:           38336 kB
Cached:           146976 kB
SwapCached:            0 kB
Active:            76316 kB
Inactive:         146260 kB
Active(anon):      39236 kB
Inactive(anon):      128 kB
Active(file):      37080 kB
Inactive(file):   146132 kB
Unevictable:           0 kB
Mlocked:               0 kB
SwapTotal:             0 kB
SwapFree:              0 kB
Dirty:                 0 kB
Writeback:             0 kB
AnonPages:         37264 kB
Mapped:            20408 kB
Shmem:              2100 kB
Slab:              96348 kB
SReclaimable:      18096 kB
SUnreclaim:        78252 kB
KernelStack:        2112 kB
PageTables:         1140 kB
NFS_Unstable:          0 kB
Bounce:                0 kB
WritebackTmp:          0 kB
CommitLimit:      498548 kB
Committed_AS:     317968 kB
VmallocTotal:   534773760 kB
VmallocUsed:       61964 kB
VmallocChunk:   534639528 kB
HugePages_Total:       0
HugePages_Free:        0
HugePages_Rsvd:        0
HugePages_Surp:        0
Hugepagesize:       2048 kB
admin@gw:~$ show version
Version:      v1.10.8
Build ID:     5142457
Build on:     11/20/18 18:10
Copyright:    2012-2018 Ubiquiti Networks, Inc.
HW model:     EdgeRouter 4
HW S/N:       788A20DFBBC5
Uptime:       14:18:53 up 1 day, 14:50,  1 user,  load average: 0.14, 0.16, 0.13
admin@gw:~$ show ubnt offload statistics |grep replaced_non_expired
ipv4_create_flow_not_found_replaced_non_expired   0
ipv6_create_flow_not_found_replaced_non_expired   58

admin@gw# show system offload ipv4 table-size table-size 131072 [edit] admin@gw# show system offload ipv6 table-size table-size 131072 [edit] admin@gw#
New Member
Posts: 38
Registered: ‎02-11-2018

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!


@waterside wrote:

@sles wrote:

@UBNT-afomins wrote:

 

 

Your feedback is highly appreciated.

 


 

you have to fix ospf.

 


Really?  That isn't very helpful at all.

 

Could you provide more detail on what you have found to be broken (specifics) or more detail on what is not working for you (again some specifics)?

 

 


 

I already provided all ospf problems since you replaced quagga with this broken implementation several times.

Just search.

And what is not helpful- no ospf fixes in change log.

 

Senior Member
Posts: 3,079
Registered: ‎08-06-2015
Kudos: 1305
Solutions: 176

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!


@sles wrote:

I already provided all ospf problems since you replaced quagga with this broken implementation several times.

Just search.

And what is not helpful- no ospf fixes in change log.


You didn't provide any information at all in your post and you didn't provide anything to me (I don't know why you would have).  I haen't done any "replacement" nor other work for you.  This is a community forum.

 

You may have provided information at another time somewhere else to someone else but we are not mind-readers.  It would be very helpful to at least provide a reference to previous postings you may have had on this issue.

 

If this was something you dealt with entirely via private support case then you should either note the ticket number here or follow-up directly on that support ticket.

 

Otherwise absolutely nobody here has any clue to what you are referring.  OSPF is working well for me and many others.

 

If you don't identify what is broken then there is nobody that can help.  If you aren't willing to at least provide some minimum basic references so that others know to what you are referring then you can't expect much in return.

 

New Member
Posts: 6
Registered: ‎10-22-2018

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Newbie question: can someone kindly point me towards the instructions for updating?

Senior Member
Posts: 3,079
Registered: ‎08-06-2015
Kudos: 1305
Solutions: 176

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!


@Whitebear wrote:

Newbie question: can someone kindly point me towards the instructions for updating?


This KB article should be of some help:  EdgeRouter - Upgrading EdgeOS Firmware

 

That covers three different options/methods (CLI, GUI, UNMS) from which to choose.

 

Emerging Member
Posts: 44
Registered: ‎09-30-2014
Kudos: 1
Solutions: 2

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

[ Edited ]

I've modified offload table-size from 131072 to 65536 and now "show ubnt offload flows" is working.

New Member
Posts: 14
Registered: ‎06-30-2018
Kudos: 1

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

There is an issue with IPv6

 

release dhcpv6-pd interface eth0
renew dhcpv6-pd interface eth0
exit

If you use the WebCLI, you will see that as soon as you use exit, logout or Ctrl-D it kills IPv6 interfaces and the WebCLI will hang until it timesout due to inactivity. 

Member
Posts: 136
Registered: ‎03-15-2016
Kudos: 37
Solutions: 5

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

I've updated two EdgeRouter X's via UNMS and it's all connected fine so far. The VPN also auto connected which doesn't always occur following a reboot.

 

Emerging Member
Posts: 77
Registered: ‎06-25-2015
Kudos: 24
Solutions: 1

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Upgraded an ER-4 through the WebGUI from 1.10.7-->1.10.8 with no ill effects.

Ubiquiti Employee
Posts: 528
Registered: ‎01-06-2017
Kudos: 190
Solutions: 20

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

@majibow

 

Thanks, we are aware of the issue and are working on a correction.

New Member
Posts: 5
Registered: ‎04-02-2016

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Upgrade failure via Web UI. Upgrading EdgeRouterX from v1.10.6

 

The same failure occurred with the prior update (v1.10.7).

 

The .tar file uploads for a while, then the error below is shown. I've tried uploading via Firefox and Chrome with the same results.

 

 

RouterUpgradeFail.png
Ubiquiti Employee
Posts: 1,161
Registered: ‎07-20-2015
Kudos: 1291
Solutions: 76

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

@sles
> you have to fix ospf.
I suppose you are talking about the "Detected router with duplicate router ID" issue that was discussed on forum fultiple times herehere and here?
Yesterday I finally was able to find reproduction scenario for "Detected router with duplicate router ID" error that randomly appears in syslog when new router joins OSPF network and creates network loop. We are still investigating this issue.

 

@SEMIJim
> My existing router sits at "configure" for 1:42. The new one sits at "configure" for 2:50!

Please post config that is loading significantly slower with new firmware

 

@ogo
> But is still present: (using show tech-support brief)
> show ipv6 route ripng (total 1)- limit 500
> % Invalid input detected at '^' marker.
Yeah, you are right, errors have been fixed in "show tech-support" and "generate tech-support archive", but for "show tech-support brief" error is still there. We shall fix this in next release.

 

@brianredbeard
> noticed the title of the GUI is now just "- ubnt" which if you run a commit from the WebCLI goes to "- ubnt - ubnt", previously was "EdgeOS - ubnt"
Thanks for pointing this out, I see same faulty title in browser tab. We shall investogate this.

 

 

@majibow
> If you use the WebCLI, you will see that as soon as you use exit, logout or
> Ctrl-D it kills IPv6 interfaces and the WebCLI will hang until it timesout due to inactivity.
We were able to reproduce this issue on lab router. Fix will be available in next release.

 

Member
Posts: 252
Registered: ‎08-15-2015
Kudos: 38
Solutions: 2

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!


@UBNT-afomins wrote:

 

@SEMIJim
> My existing router sits at "configure" for 1:42. The new one sits at "configure" for 2:50!

Please post config that is loading significantly slower with new firmware

 


Please disregard, @UBNT-afomins. The config actually loads faster on the new router, with 1.10.8, than it did on the old router with 1.9.x: 1:15, now.

 

I'm going to guess it was either the fact I had missing scripts referened in the config (see earlier posts), the fact it wasn't plugged into anything other than power and console port, or both.

 

Thanks for the follow-up and please accept my apologies for the false alarm.

 

Member
Posts: 299
Registered: ‎02-12-2013
Kudos: 81
Solutions: 23

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Hi @bhamail
It's a known bug in 1.10.6, where upgrading to any other version would give an error in the GUI, but the update is still applied and you just need to restart the router to activate it.
Have a look at the 1.10.7 release notes:
https://community.ubnt.com/t5/EdgeMAX-Updates-Blog/EdgeMAX-EdgeRouter-software-release-v1-10-7/ba-p/...
New Member
Posts: 5
Registered: ‎04-02-2016

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Thanks @flamber ! After reboot, the device showed 1.10.7. Then I was able to upgrade to 1.10.8 via the Web UI.

Emerging Member
Posts: 48
Registered: ‎09-05-2016
Kudos: 3
Solutions: 2

Re: EdgeMAX EdgeRouter software version v1.10.8 has been released!

Upgrade to 1.10.8 went smooth on my X SFP.

Thank U

Reply