Reply
New Member
Posts: 14
Registered: ‎02-07-2017
Accepted Solution

FiberHome AN5516-04 configuration

So I am attempting to test the uFiber Nano G unit with my FiberHome AN5516-04 (FW version: VR3.2) but curious on how to set it up within FiberHome OLT?

 

The NMS you can setup as bridge, routed, etc. I had to whitelist the device for ONU authentication but would like to pass data through the unit. We do have a vlan tag we normally use for the FiberHome ONT's and if we need to remove the vlan tag we could.

 


Accepted Solutions
Ubiquiti Employee
Posts: 2,970
Registered: ‎10-05-2015
Kudos: 1162
Solutions: 232

Re: FiberHome AN5516-04 configuration

 @zulander Could you try to set this on the FiberHome? 

 

Admin\gponline# set pon_interconnection_switch slot 1 switch enable union_interconnect_switch enable

View solution in original post


All Replies
New Member
Posts: 14
Registered: ‎02-07-2017

Re: FiberHome AN5516-04 configuration

@UBNT-Jordan is there any documentation or something that could point me in a direction? I am still trying to get it to work. The ONU is on the latest firmware as well.

Ubiquiti Employee
Posts: 2,970
Registered: ‎10-05-2015
Kudos: 1162
Solutions: 232

Re: FiberHome AN5516-04 configuration

Hi @zulander I have updated this article with some more details. Is the NanoG set to Profile 3?

New Member
Posts: 14
Registered: ‎02-07-2017

Re: FiberHome AN5516-04 configuration

@UBNT-Jordan I believe Profile 2. I will be going back onsite shortly and will change to profile 3 if it wasn't already.

New Member
Posts: 14
Registered: ‎02-07-2017

Re: FiberHome AN5516-04 configuration


@zulander wrote:

@UBNT-Jordan I believe Profile 2. I will be going back onsite shortly and will change to profile 3 if it wasn't already.


@UBNT-Jordan it was set to Profile 3 before. It greens up and stays active but unable to pass data through the ONU to the OLT. Anything specific need to be set on the FiberHome OLT? We normally setup the WAN Information in the NMS with a vlan tag in router mode. I tried bridge with no success either.

New Member
Posts: 14
Registered: ‎02-07-2017

Re: FiberHome AN5516-04 configuration

@UBNT-Jordan so Sunday night I began to troubleshoot with FiberHome on the OLT to see if we could get traffic to pass with no success. Any type of configuration we need to perform on the ONT for it to pass traffic? We would like to have the LAN port untagged and PON port tagged a vlan since the uplink at the OLT is tagged with a vlan.

Ubiquiti Employee
Posts: 2,970
Registered: ‎10-05-2015
Kudos: 1162
Solutions: 232

Re: FiberHome AN5516-04 configuration

 @zulander Could you try to set this on the FiberHome? 

 

Admin\gponline# set pon_interconnection_switch slot 1 switch enable union_interconnect_switch enable
New Member
Posts: 14
Registered: ‎02-07-2017

Re: FiberHome AN5516-04 configuration

That worked. Once I configured the ONT within the FiberHome NMS software I had to power cycle the ubiquiti device.

New Member
Posts: 4
Registered: ‎07-11-2017

Re: FiberHome AN5516-04 configuration

Hi Zulander,

 

 

New Member
Posts: 14
Registered: ‎02-07-2017

Re: FiberHome AN5516-04 configuration

Oh change your device name in the ONT to GPONxxxx. Also you will need to setup authentication on the PON port. When I enabeld authentication on the PON port I just whitelisted it to get it up and running easily.

Reply