Reply
Regular Member
Posts: 318
Registered: ‎05-26-2016
Kudos: 67
Solutions: 3

Re: [USG] Firmware v4.4.29 now available

Don't fix it if it ain't broke. I'd wait until you get a complaint of performance (and can see the stats that match that complaint). Though I don't listen to my own words, just because a firmware advertises "better performance" doesn't mean you'll actually see/feel it. That all being said, I think there is a common feeling among tech people, almost an addiction to two things: Speed Tests & Updates
New Member
Posts: 32
Registered: ‎02-08-2018
Kudos: 1
Solutions: 1

Re: [USG] Firmware v4.4.29 now available

Well, couldn't give up!
Forgot both my USG's and factory reset. Upgraded FW again to 4.4.29, gúess what, now I get IP from my ISP and all up and running again. But must say its a pain each time so one should not really, still cant help to upgrade in case somethings get better ;-)
New Member
Posts: 8
Registered: ‎05-25-2018

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

This update has caused nothing but headaches.  After updateing the unit will show connected then drops off line.  I have had to roll back firmware manually multiple times and attempted updating through CLI and GUI.  Unbeleivably frustrating.  Internet is up, I have a blue light, but it still shows disconnected.  Any ideas?

 

Update:  Occasionally the unit will pop up and go into a provision and then show disconnected again.  Cant SSH acces router when disconnected either.  And the POS is extremely hot.

Member
Posts: 144
Registered: ‎09-09-2015
Kudos: 18
Solutions: 2

Re: [USG] Firmware v4.4.29 now available

I'm having problem with .29 aswell... Goes into a adoption loop... 

Stays Adopting for about 5 min then disconnected and the Adopting 5 min again and so on...

Please give kudo's to the people who have helped you and mark your thread as solved when you receive a solution to your issue.
New Member
Posts: 14
Registered: ‎01-05-2018

Re: [USG] Firmware v4.4.29 now available

16 hours in, no issues. Controller 5.8.30

New Member
Posts: 11
Registered: ‎05-03-2017
Kudos: 7
Solutions: 1

Re: [USG] Firmware v4.4.29 now available

Likewise, I've got 23 hours on 3 separate sites, controller 5.9.26 and no issues.
New Member
Posts: 7
Registered: ‎06-22-2018

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

Upgraded USG-3P from 4.4.28 to 4.4.29 approximately 10 hours ago.

 

No problems.


CloudKey 0.12.0 / Controller 5.9.29
USG-3P 4.4.29.5124210
USW-16-150W 3.9.54.9373
2x UAP-AC-PRO 3.9.54.9373
New Member
Posts: 10
Registered: ‎06-06-2018

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

So I've just finished updating the USG 3P and it appears to be stuck in this adoption loop. I tried to SSH into device and this is what INFO returned:

 

Model: UniFi-Gateway-3
Version: 4.4.29.5124210
MAC Address: fc:ec:da:49:e5:82
IP Address: 0.0.0.0
Hostname: USG3P
Uptime: 1335 seconds

Status: Server Reject (http://192.168.1.252:8080/inform)

 

How would one go about fixing this? Thanks

 

Edit1: Forgot to mention that I was going from 4.4.28 that was released recently. I also applied the speedtest patch.

 

Edit2: SSH'ed into the USG and used the set-default command to reset everything back to default. After the automatic reboot, controller was able to provision the device correctly. and now it's connected.

New Member
Posts: 4
Registered: ‎04-14-2018

Re: [USG] Firmware v4.4.29 now available

Does anyone from Ubiquiti know if this was meant to upgrade the core OS? I’m still stuck on Wheezy...

New Member
Posts: 3
Registered: ‎07-20-2018

Re: [USG] Firmware v4.4.29 now available

this morning there were 2 updates showwing in miy controller for de USG3P

deleted the 4.4.28 

and installed the 4.4.29  , in the controller (5.8.30 ) on CK (0.11.12)

all looks good afther 8 minutes up and running again 

UniFi USG Security Gateway Router
Unifi Switch 8 - 60W
Unifi Switch 8 -150W
Ubiquiti Unifi AC Pro
UniFi Cloud Key
New Member
Posts: 10
Registered: ‎02-23-2018
Kudos: 1

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

 

Like everyone else, had issues with 4.4.28. I upgraded to 4.4.29 with success. However, USG dropped off the network as soon as I turned on IPS.  DPI was already enabled.

 

USG would only come back online after restarting and turning off IPS.  I reverted back to 4.4.22

 

I'm running controller 5.9.26

 

Emerging Member
Posts: 62
Registered: ‎06-29-2017
Kudos: 8

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

I just upgraded my USG from v4.4.28 which was working perfectly to v4.4.29. The USG although working, just shows as disconnected in UniFi. I've tried rebooting it without success. How do I get it back again?

 

EDIT: actually scratch that, it's just come back by itself but still has 4.4.28 in it. Might just leave it alone for now, the software still doesn't "feel" like it's there just yet...

New Member
Posts: 2
Registered: ‎01-24-2016

Re: [USG] Firmware v4.4.29 now available

No problems upgrading USG 4 to firmware V4.4.29 from V4.4.28. running Cloud Key gen 2 plus on controller 5.8.30.

New Member
Posts: 8
Registered: ‎05-25-2018

Re: [USG] Firmware v4.4.29 now available

Is anyone who has upgraded successfully running DPI and IPS?  

Regular Member
Posts: 387
Registered: ‎09-28-2017
Kudos: 99
Solutions: 29

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

@gator911 Yes, I am.

USG3

 

Edit_____________

 

I only just upgraded yesterday and I haven't received any IPS hits yet, so maybe not successfully.  They are both turned on, if that's what you're asking.

New Member
Posts: 15
Registered: ‎04-14-2018
Kudos: 3

Re: [USG] Firmware v4.4.29 now available

Upgraded USG3 on two sites.

No 1 (the one where the controller is running) went smooth and is now up and running roughly 24h

No 2 (a remote one connecting to the controller through the internet) went smooth but soon after was in "disconnected" state. 

 

A quick look shows something like a memory leak. Are there any recommended steps?

 

Controller is 5.8.30, USGs are now on 4.4.29.

usg.png
New Member
Posts: 6
Registered: ‎10-11-2016
Kudos: 1

Re: [USG] Firmware v4.4.29 now available

DPI yes, works fine for months now through many firmware versions.

IPS sadly NO, soon after I enable it seems like something kills comms, latency/throughput dials go amber and nothing works to internet.

I have disabled IPS, left DPI on for some hours now and so far no issues, will keep an eye and update should it change.

New Member
Posts: 35
Registered: ‎10-14-2016
Kudos: 6
Solutions: 1

Re: [USG] Firmware v4.4.29 now available

i just updated my usg 3 with dpi and ids (no ips yet). i will let it run for a week before enabling ips

New Member
Posts: 7
Registered: ‎06-22-2018

Re: [USG] Firmware v4.4.29 now available

[ Edited ]

I am running DPI but I am NOT running IPS and/or VLANs.

 

USG-3P running 36 hours on 4.4.29 with no problems.


CloudKey 0.12.0 / Controller 5.9.29
USG-3P 4.4.29.5124210
USW-16-150W 3.9.54.9373
2x UAP-AC-PRO 3.9.54.9373
New Member
Posts: 10
Registered: ‎06-06-2018

Re: [USG] Firmware v4.4.29 now available

Hmmm.... Maybe I'm facing the same issue. It's weird because website says 41.88% for memory, but the mobile app says 81.07%. Not really sure which to trust.

Reply