Reply
Highlighted
New Member
Posts: 1
Registered: ‎11-12-2018

UniFi Switch 16 POE Infinity Loop

[ Edited ]

Hi

 

I have a problem with this swith, the swith is in infinty reset loop y try to do a hard reset however not fixed

 

I conneted by Console port and appear:

 

[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 61952
[    0.000000] Kernel command line: console=ttyS0,115200 mem=128M@0x0 mem=128M@0x68000000 mtdparts=spi1.0:768k(u-boot),64k(u-boot-env),64k(shmoo),15360k(kernel0),15424k(kernel1),1024k(cfg),64k(EEPROM) ubntbootid=0 ubootver=usw-v1.1.3.109-g90a2a80b
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 128MB 128MB = 256MB total
[    0.000000] Memory: 246116k/246116k available, 16028k reserved, 131072K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xf0000000   ( 632 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0018000 - 0xc0311fc0   (3048 kB)
[    0.000000]       .init : 0xc0312000 - 0xc0d51880   (10495 kB)
[    0.000000]       .data : 0xc0d52000 - 0xc0d7a180   ( 161 kB)
[    0.000000]        .bss : 0xc0d7a1a4 - 0xc0d8c658   (  74 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:292
[    0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[    0.010000] Calibrating delay loop... 795.44 BogoMIPS (lpj=3977216)
[    0.050000] pid_max: default: 4096 minimum: 301
[    0.050000] Mount-cache hash table entries: 512
[    0.050000] CPU: Testing write buffer coherency: ok
[    0.050000] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.050000] Setting up static identity map for 0x253330 - 0x253388
[    0.050000] L310 cache controller enabled
[    0.050000] l2x0: 8 ways, CACHE_ID 0x410000c9, AUX_CTRL 0x0a120000, Cache size: 131072 B
[    0.050000] Brought up 1 CPUs
[    0.050000] SMP: Total of 1 processors activated (795.44 BogoMIPS).
[    0.050000] devtmpfs: initialized
[    0.060000] NET: Registered protocol family 16
[    0.060000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.060000] GENPLL[5] mdiv=40 rate=2000000000
[    0.060000] Sel=1 Ovr=1 Div=48
[    0.060000] UART clock rate 50000000
[    0.080000] bio: create slab <bio-0> at 0
[    0.080000] Switching to clocksource iproc_gtimer
[    0.080000] NET: Registered protocol family 2
[    0.090000] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.090000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.090000] TCP: Hash tables configured (established 4096 bind 4096)
[    0.090000] TCP: reno registered
[    0.090000] UDP hash table entries: 128 (order: 0, 4096 bytes)
[    0.090000] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
[    0.090000] NET: Registered protocol family 1
[   13.520000] pm_init: Initializing Power Management ....
[   13.520000] iproc gpiochip add GPIOA
[   13.520000] GPIOA:ioaddr f0000060
[   13.520000] GPIOA:intr_ioaddr f0000000 dmu_ioaddr   (null)
[   13.770000] PCIE0: LINKSTA reg 0xbe val 0x1001
[   13.770000] reg[0xac]=0x10, reg[0xae]=0x42, reg[0xb0]=0x8000, reg[0xb4]=0x2c10, reg[0xb6]=0x10, reg[0xb8]=0x5c12, reg[0xba]=0x65, reg[0xbe]=0x1001, reg[0xc6]=0x40, reg[0xca]=0x1, reg[0xd0]=0x1f, reg[0xd2]=0x8, reg[0xdc]=0x1, PCIE0 link=0
[   14.020000] PCIe port 1 in End-Point mode - ignored
[   14.020000] Registering iproc_pmu_device
[   14.020000] bounce pool size: 64 pages
[   14.040000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   14.040000] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[   14.040000] msgmni has been set to 224
[   14.040000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[   14.040000] io scheduler noop registered
[   14.040000] io scheduler deadline registered (default)
[   14.040000] io scheduler cfq registered
[   14.040000] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[   14.040000] serial8250.0: ttyS0 at MMIO 0x18000400 (irq = 123) is a 16550A
[   14.490000] console [ttyS0] enabled
[   14.490000] serial8250.0: ttyS1 at MMIO 0x18000300 (irq = 123) is a 16550A
[   14.520000] brd: module loaded
[   14.530000] loop: module loaded
[   14.540000] nbd: registered device at major 43
[   14.570000] tun: Universal TUN/TAP device driver, 1.6
[   14.570000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   14.580000] TCP: cubic registered
[   14.580000] NET: Registered protocol family 10
[   14.590000] sit: IPv6 over IPv4 tunneling driver
[   14.600000] NET: Registered protocol family 17
[   14.600000] 8021q: 802.1Q VLAN Support v1.8
[   14.610000] GENPLL[5] mdiv=40 rate=2000000000
[   14.610000] qspi_iproc qspi_iproc.1: 1-lane output, 3-byte address
[   14.620000] m25p80 spi1.0: found mx25l25635e, expected m25p80
[   14.630000] m25p80 spi1.0: mx25l25635e (32768 Kbytes)
[   14.630000] 7 cmdlinepart partitions found on MTD device spi1.0
[   14.640000] Creating 7 MTD partitions on "spi1.0":
[   14.640000] 0x000000000000-0x0000000c0000 : "u-boot"
[   14.650000] 0x0000000c0000-0x0000000d0000 : "u-boot-env"
[   14.660000] 0x0000000d0000-0x0000000e0000 : "shmoo"
[   14.660000] 0x0000000e0000-0x000000fe0000 : "kernel0"
[   14.670000] 0x000000fe0000-0x000001ef0000 : "kernel1"
[   14.680000] 0x000001ef0000-0x000001ff0000 : "cfg"
[   14.690000] 0x000001ff0000-0x000002000000 : "EEPROM"
[   14.710000] Freeing init memory: 10492K
[   14.760000] ubnthal: module license 'Proprietary' taints kernel.
[   14.760000] Disabling lock debugging due to kernel taint
[   14.830000] gpiodev: reset_timeout=3
...running /sbin/init
init started: BusyBox v1.19.4 (2017-03-14 09:07:24 PDT)
/bin/watchdog: invalid option -- m
BusyBox v1.19.4 (2017-03-14 09:07:24 PDT) multi-call binary.

Usage: watchdog [-t N[ms]] [-T N[ms]] [-F] DEV

Periodically write to watchdog device DEV

        -T N    Reboot after N seconds if not reset (default 60)
        -t N    Reset every N seconds (default 30)
        -F      Run in foreground

Use 500ms to specify period in milliseconds

+ exec
SyncDB Running...
Restoring EEPROM data from ubnthal
MAC: fc:ec:da:71:e3:63
Validating the active image /dev/mtd3..."3.7.48.6200"
Validating the backup image /dev/mtd4..."3.7.48.6200"
DMA pool size: 4194304
AXI unit 0: Dev 0x8343, Rev 0x01, Chip BCM53343_A0, Driver BCM56150_A0
SOC unit 0 attac[   29.710000] Received 2 PSE boards registered with pid 739
hed to PCI device BCM53343_A0


<10> Jan  1 00:00:38 0.0.0.0-1 UBNT_POE[67709796]: ubnt_poe_common.c(4930) 1 %% PSE init failed 0x000f, retry 1

<10> Jan  1 00:00:41 0.0.0.0-1 UBNT_POE[67709796]: ubnt_poe_common.c(4930) 2 %% PSE init failed 0x000f, retry 2

<10> Jan  1 00:00:45 0.0.0.0-1 UBNT_POE[67709796]: ubnt_poe_common.c(4930) 3 %% PSE init failed 0x000f, retry 3

<10> Jan  1 00:00:45 0.0.0.0-1 UBNT_POE[67709796]: ubnt_poe_common.c(3618) 4 %% PoE Initialization failed in Hardware

cnfgrApiCallback: Failed by task 0x4092b64 in file ubnt_poe_cnfgr.c line 201.
log_error_code cnfgr_tally.c  199

Switching software SIGSEGV Handler
This build was configured to copy this crash information to
  a file.
+ exec
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
[   51.160000] Disabling non-boot CPUs ...
[   51.160000] Restarting system.


U-Boot usw-v1.1.3.109-g90a2a80b (Nov 02 2016 - 20:22:35)

DEV ID= 0000db56
SKU ID = 0x8343
DDR type: DDR3
MEMC 0 DDR speed = 667MHz
Validate Shmoo parameters stored in flash ..... OK
Press Ctrl-C to run Shmoo ..... skipped
Restoring Shmoo parameters from flash ..... done
Running simple memory test ..... OK
DDR Tune Completed
DRAM:  256 MiB
WARNING: Caches not enabled

 soc_pcie_hw_init : port->reg_base = 0x18012000 , its value = 0x1
PCIe port 0 in RC mode

 pos is 172
==>PCIE: LINKSTA reg 0xbe val 0x1001

**************
 port 0 is not active!!
**************
In:    serial
Out:   serial
Err:   serial
Unlocking L2 Cache ...Done
arm_clk=400MHz, axi_clk=200MHz, apb_clk=50MHz, arm_periph_clk=200MHz
Disabling outer cache
Net:   Board Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0

 

Caould any help me to restore this switch ?

 

Thanks

 

 

Reply