Reply
New Member
Posts: 5
Registered: ‎02-04-2017
Kudos: 1

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

Do it via CLI. This is the only way to get it done.

New Member
Posts: 24
Registered: ‎08-30-2016
Kudos: 3

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

DO NOT UPDATE !

 

Completly unstable with Controller 5.6.40 ... 

New Member
Posts: 17
Registered: ‎11-10-2016
Kudos: 3

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

Doesn't work on our Gen1 units, and we don't want to risk TFTP after the reports of bricked units.

New Member
Posts: 3
Registered: ‎07-30-2016

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable


@mjmrad wrote:

Doesn't work on our Gen1 units, and we don't want to risk TFTP after the reports of bricked units.


Definitly don't try the TFTP mrthod bricked 2 of my Gen 1 units .... very poor suport / advice causing trama everywhere

New Member
Posts: 33
Registered: ‎04-22-2017
Kudos: 2

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

I have been able to TFTP 4.15 to my gen 1 AP but now it is constantly booting (organe flashing light). Any suggestions?

New Member
Posts: 5
Registered: ‎11-30-2018

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

All i can say about tftp from my experience is once you upload the new firmware and pimpkin says done etc.... Leave it..... Dont unplug it... Touch it or anything... I left mine ten mins.. Then unplugged it from pc and then plugged into network. Worked on all x4 uap-lr v2

Emerging Member
Posts: 90
Registered: ‎01-14-2016
Kudos: 14
Solutions: 2

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

Untitled-2.jpgI have been watching this thread.  So far smooth sailing for me with 4.0.21.9965 across the board with controller 5.10.17.  I rolled out to the AP-LR & Outdoor+ devices the firmware from the 'Stable Candidate' post, as I know it was not available on the 'Stable' announcement.  All the upgrades were done from the management interface, no CLI or TFTP.  I had a short power outage early in the week which rebooted a bunch of stuff, otherwise it has been all good for 12 days since doing the upgrade.

 

I am not sure this helps anyone, but at least it is a success story among all the doom and gloom on this thread.

 

Thanks,

-Eric

 

New Member
Posts: 14
Registered: ‎06-07-2018
Kudos: 2

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

@remcoveugen wrote:

You can do a downgrade via the managementconsole :

 

Use this link as a custom firmware (voor the UAP/LR UAP)

 

Firmware Link Removed

 

Works for me !


Thanks mate this worked for me too....

All stable now.

Cheers2

 

Established Member
Posts: 880
Registered: ‎10-09-2010
Kudos: 107
Solutions: 7

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

i cant do tftp cus 6 sites are in remote areas and its not practical to pull from the ceiling  to do each and every gen1 uaps ,

wonder any one has wireless uplink  and also with US150w ?

because of the wireless uplink enabled on my site  the whole network is going crazy with stp blocking  on every port.

 

Since I disable wireless uplink its comedown for now I will keep it as it is only one uap is wireless uplinked and its down now which is fin e  

New Member
Posts: 1
Registered: ‎05-27-2016

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

This was very helpful. That link actually works with the customer firmware option. Thanks. Saved me a lot of time.

New Member
Posts: 17
Registered: ‎11-10-2016
Kudos: 3

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

@remcoveugen wrote:

You can do a downgrade via the managementconsole :

 

Use this link as a custom firmware (voor the UAP/LR UAP)

 

Firmware Link Removed

 

Works for me !


I was skeptical, but went ahead and tried this firmware, and it worked!  I'm just curious, though, what is different about this 4.0.15 firmware versus the one that is posted on Ubiquiti's download page?

New Member
Posts: 24
Registered: ‎12-01-2016
Kudos: 6

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

With that link i managed to downgrade my 3 ap-lr but I cannot pass that firmware to my ac-lite and and ac-pro. This 2 devices with v21 have lost almost half their power.

 

Is there a link for this 2 also because so far the firmwares where the same between all my ap's

CloudKey (1): v0.13.4.410e9b6.190213.1205 / Controller: 5.10.17-11638-1
UniFi USG(1): 4.4.36.5146617
US‑8‑60W (11): 4.0.21.9965
UniFi AP-LR,AC-Lite,AC-Pro (5): 4.0.15.9872
NanoBeam 5AC 19(2): XC.v8.5.8
New Member
Posts: 17
Registered: ‎11-10-2016
Kudos: 3

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

@bluechris wrote:

With that link i managed to downgrade my 3 ap-lr but I cannot pass that firmware to my ac-lite and and ac-pro. This 2 devices with v21 have lost almost half their power.

 

Is there a link for this 2 also because so far the firmwares where the same between all my ap's



Chris,

 

I haven't noticed any problems with the new firmware on the newer AC units.  However, if you want to downgrade them to 4.0.15, the firmware on Ubiquiti's download page should work.  I tested it.

 

https://www.ui.com/download/unifi

Click "Past Firmware"

 

Then, just go to "Custom Firmware" from within the UniFi Controller interface and paste the appropriate URL.

New Member
Posts: 14
Registered: ‎06-07-2018
Kudos: 2

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable


@bluechris wrote:

With that link i managed to downgrade my 3 ap-lr but I cannot pass that firmware to my ac-lite and and ac-pro. This 2 devices with v21 have lost almost half their power.

 

Is there a link for this 2 also because so far the firmwares where the same between all my ap's


Yeah i think that this link is just for the UAP and UAP-LR

 

 

New Member
Posts: 17
Registered: ‎11-10-2016
Kudos: 3

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable


@Robbieboy43 wrote:

@bluechris wrote:

With that link i managed to downgrade my 3 ap-lr but I cannot pass that firmware to my ac-lite and and ac-pro. This 2 devices with v21 have lost almost half their power.

 

Is there a link for this 2 also because so far the firmwares where the same between all my ap's


Yeah i think that this link is just for the UAP and UAP-LR

 

 


See my previous post and download from ui.com

Emerging Member
Posts: 51
Registered: ‎09-23-2017
Kudos: 3

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

@Robbieboy43 wrote:

@remcoveugen wrote:

You can do a downgrade via the managementconsole :

 

Use this link as a custom firmware (voor the UAP/LR UAP)

 

Firmware Link Removed

 

Works for me !


Thanks mate this worked for me too....

All stable now.

Cheers2

 


Downgrading UAP v1 and UAP-LR v1 works using this link. Thanks.

Emerging Member
Posts: 74
Registered: ‎02-24-2018
Kudos: 24
Solutions: 2

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

@remcoveugen wrote:

You can do a downgrade via the managementconsole :

 

Use this link as a custom firmware (voor the UAP/LR UAP)

 

Firmware Link Removed

 

Works for me !


This also worked for me on a UAP-LR V1

My AP is working fine again.
Thanks. And no thanks to Ubiquiti and their silence on the issue.

New Member
Posts: 1
Registered: ‎02-16-2019

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

 

 

You can do a downgrade via the managementconsole :
Use this link as a custom firmware (voor the UAP/LR UAP)
Firmware Link Removed
Works for me !

10x!!! Works for me too.

New Member
Posts: 24
Registered: ‎12-01-2016
Kudos: 6

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

Ok thank you guys. From the official download page i managed to downgrade my ac-lite and ac-pro to 4.15.

Now i will see in Monday if everything is working correctly. 

CloudKey (1): v0.13.4.410e9b6.190213.1205 / Controller: 5.10.17-11638-1
UniFi USG(1): 4.4.36.5146617
US‑8‑60W (11): 4.0.21.9965
UniFi AP-LR,AC-Lite,AC-Pro (5): 4.0.15.9872
NanoBeam 5AC 19(2): XC.v8.5.8
New Member
Posts: 2
Registered: ‎06-08-2018
Kudos: 2

Re: [FIRMWARE] 4.0.21.9965 for UAP/USW has been released | Stable

[ Edited ]

For what i have been reading the last firmware used a new format/kernel/framework in the background. The link that was posted is the. 15 firmware on the new format/kernel/framework

Reply